How to Apply a Wall Sticker

Tips for posing for a decorative medium size (h or L < 60 cm)

Pass a scraper on your sticker
Each sticker is composed of a white protective paper, a pattern and a transparent transfer paper. Before laying, ensure you have a rigid object such as a telephone or credit card, ideally a raclette).
Proceed several times the squeegee from the Center to the edges to adhere the pattern on the transparent transfer paper.

Remove the protective paper
Once the passage of the squeegee is completed, gently separate the white protective paper while leaving the ground stuck on the transparent transfer paper.

Prepare the holder d ‘ application, position and stick on the wall
Always prefer smooth surfaces (satinées, lacquered or laminated) and clean (dust, wash and dry your surface prior to application).
The grip is optimal in these conditions.

Once the final location of your chosen sticker, place and paste it.

Remove the transfer paper
Now your sticker is pasted on your wall, also pass the squeegee again so that the pattern is well glued on the wall.)
You can remove the transparent transfer paper by pulling gently at an angle of 180 °. You can still give a squeegee on the edges of the sticker.

Tip: If you have small air bubbles that appear, Pierce them carefully with a fine needle.

Council of posing for large format (h or L > 60 cm) sticker

Spend a squeegee (or something flat and rigid as a rule) on your sticker
Each sticker is composed of a white protective paper, a pattern and a transparent transfer paper. Prior to installation, please have a rigid object like a telephone or credit card, ideally a squeegee (available soon on the site).
Proceed several times the squeegee from the Center to the edges to adhere the pattern on the transparent transfer paper.

Position and stick on the wall
Once the final location of your chosen sticker, place and paste it.
Always prefer smooth surfaces (satinées, lacquered or laminated) and clean (dust, wash and dry your surface prior to application).
The grip is optimal in these conditions.

Keep the sticker on the wall in l ‘ using ‘ tape of masking in the middle of the sticker
This adhesive is commonly used in paint to protect unpainted areas. Otherwise, Scotch can do l ‘ case.
Put sticky Strip to keep the sticker on the wall on half of its height.

Remove the protective paper in half the time
Cut out with scissors or cutter protective paper on l ‘ one of the halves separated by l ‘ adhesive of masking
Once the passage of the squeegee is completed, gently separate the white protective paper while leaving the ground stuck on the transparent transfer paper.
Repeat the same operation for the second half of the sticker

Remove the paper transfer in one piece
Now that your sticker is stuck on your wall, also pass the squeegee again so that the pattern is well glued on the wall.
You can remove the transparent transfer paper by pulling gently at an angle of 180 °. You can still give a squeegee on the edges of the sticker.

Tip: If you have small air bubbles that appear, Pierce them carefully with a fine needle.

Tips for posing for a sticker to climb (to paste into several parts)

The principle is the same as described above.
Proceed simply wall sticker on a part-by-part and be sure especially to adjust the fittings between the parties to stick to a good straight pose.

Tips for posing for a sticker on a glass surface

The procedure is identical to that described above.
Once the white protective film is removed, it should be a little spray d ‘ water on the sticker with his paper transparent transfer for a better grip.

Council of pose for a portable computer sticker or iPod >

Prepare the holder d ‘ application
Clean your computer or iPod to l ‘ using ‘ a damp sponge and dry with a non fluffy cloth.
The surface must be free of dust, because each particle can generate a visible mark once the sticker stuck.
The grip and the rendering will be perfect in these conditions.

Take off the white protective paper sticker

Start l ‘ application on an entire width or height of the support
The positioning of the sticker to the start condition a perfect straight pose.
Take the time d ‘ optimize this investment at best.
The used vinyl tolerates a multiple repositioning to the pose.

Spend a raclette or a flat and rigid object on your sticker as the collage (laptop)

Tip: If you have small air bubbles that appear, Pierce them carefully with a fine needle.

Storage Board

Store adhesives to flat or rolled up in a clean place to l ‘ shelter from the Sun and l ‘ moisture. Maintain a temperature of between 10 and 25 ° C. The duration of storage should not exceed 1 year.